







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
See the difference
Before
After
Before
After
Before
AfterBrick Paver Driveway in Mesquite, NV
A brick paver driveway in Mesquite typically runs $9 to $18 per square foot installed, and most residential driveways here land somewhere between $5,500 and $16,000 depending on size, base prep, and pattern. We install clay and concrete brick pavers over a compacted aggregate base built for the desert’s movement, so the surface stays flat through summer heat and the occasional monsoon wash rather than settling into ruts within a couple of seasons.
Mesquite sits in a stretch of the Mojave where the ground can be caliche-hard one foot down and expansive clay the next, and where summer surface temperatures on bare concrete climb high enough to make a front yard unusable by mid-afternoon. Brick pavers handle both conditions well: individual units flex with minor soil movement, and an open-joint or permeable joint sand lets water move through instead of sheeting off. What matters is that whoever installs the driveway gets the base compaction, edge restraint, and drainage grading right. That’s where most paver driveways fail, and it’s where we spend the most time.
Our team at Groundwork Construction Co. of Mesquite takes on full-scope exterior work, and our technicians bring up to 12 years of hands-on experience with paver systems. Every project is covered by our 730-Day Done Right Promise – if it’s not done right, we make it right. You can reach a live person 24/7 at (888) 413-6358, whether you’re planning a spring install or a tear-out of a driveway that’s already failing.
If you’re mapping out the whole exterior, our Driveway & Pavers in Mesquite page covers the broader range of hardscape options, and you can always start from our home to see how driveways fit into a full property plan.

When You Need Brick Paver Driveway
Most Mesquite homeowners don’t call us because they want something beautiful. They call because something is already going wrong, or because they’re tired of patching the same spot. Here are the situations we see most:
- Your concrete driveway has cracked along the expansion joints. In the older parts of town, especially around the original neighborhoods near Mesquite Boulevard, we routinely see 20-plus-year-old slabs that have heaved and separated as the underlying soil moves through wet winters and dry summers. Patching that crack is a temporary fix – a paver replacement with a properly compacted base resolves the cause, not just the symptom.
- Your current driveway washes out every monsoon season. A driveway graded flat instead of toward the street or a drainage swale will pond water and erode at the edges. We see this a lot on sloped lots near the golf course communities north of I-15, where the grade has to be tied into the house pad carefully.
- The surface is too hot to walk on barefoot in July. Standard gray concrete bakes in direct sun. Lighter-toned brick pavers, especially sand-set units with reflective tones, stay cooler underfoot and are far easier to repair if a single brick chips or stains.
- You’re updating curb appeal before listing the house. A well-installed brick paver driveway reads as a considered upgrade, not a patch job. Buyers notice the difference between a driveway that looks original to the house and one that looks finished.
- You’ve already had a paver driveway but the edges keep spreading. This almost always means the edge restraint wasn’t set into concrete or the base wasn’t deep enough. We re-lay these regularly – pulling the field units, correcting the base, and re-setting the edge properly.
- You need to widen or add a turnaround for a second vehicle. Adding onto an existing driveway is a common request for households with a boat, trailer, or third car. Brick pavers let you match the existing field pattern or deliberately contrast the addition, so the driveway reads as one design rather than two.
Our Brick Paver Driveway Process
Installing a paver driveway that holds up for decades is mostly subtractive work – what comes out and how carefully the base goes back in matters more than the pattern you pick for the top. Here’s how we run a job, start to finish:
- Site assessment and drainage plan. We walk the driveway length, check the slope away from the house pad and garage floor, and map where water needs to go. If the existing surface tiles, we check the subgrade to see how deep the problem runs. We’ll also discuss paver style and color at this stage – whether you’re matching the house’s roofline tone or going higher-contrast.
- Demolition and disposal. Existing concrete, asphalt, or failing pavers come out, and we haul off the debris. On driveways with old tree roots pushing up sections, we cut out and treat the root zone before the base goes back in.
- Base excavation and compaction. We excavate to a depth that suits the traffic load – typically 4 to 6 inches of compacted aggregate base under a paver driveway, compacted in lifts rather than dumped in one pass. The base gets graded to the drainage plan, not to a flat plane, and we keep the checkpoints documented along the way.
- Edge restraint and bedding sand. We set a concrete or steel edge restraint along both sides of the driveway to lock the field units in place. Without that, the pavers migrate outward in the heat and spread. Bedding sand is screeded to a consistent depth so the finished surface stays level.
- Paver installation and pattern layout. We set the field pattern – herringbone, running bond, basketweave, or a combination – with cuts measured to avoid sliver pieces at the edges. Each paver is set, checked, and adjusted as we go rather than hammered into place.
- Joint sand, compaction, and final walkthrough. Polymeric joint sand goes in, we compact the full field to seat the pavers, then sweep and cure the sand per the manufacturer’s spec. We walk the finished driveway with you, review the care and resealing recommendations, and hand over the warranty documentation for our 730-Day Done Right Promise.
Most paver driveways we install in Mesquite take between three and six working days, weather permitting. We schedule so a single crew owns the job from demolition through the final compaction pass.

Brick Paver Driveway Pricing in Mesquite
Brick paver driveways in Mesquite typically cost $9 to $18 per square foot installed, with the wide range reflecting base depth, pattern complexity, and paver material. A standard 20×20-foot single-car driveway runs roughly $3,600 to $7,200, while a full three-car driveway of 600 to 800 square feet falls in the $5,400 to $14,400 range. Heavier traffic or a wider turnaround can push total project cost to $16,000 or more. These are the real-world numbers we work with, and we give them to you upfront in writing so you can plan accordingly.
Here’s what drives the cost up or down on a Mesquite job:
- Base depth and soil conditions. A driveway with intact, compaction-tested subgrade is faster and cheaper to install. Caliche or expansive clay that needs over-excavation adds line items for the additional aggregate and labor.
- Paver material and pattern. Standard concrete pavers cost less per square foot than clay brick, and herringbone patterns use more material and more cutting time than a straightforward running bond. We work with Belgard paver systems as our go-to brand – their units hold their color and edges well through heat cycling.
- Drainage corrections. If the site needs a channel drain, a French drain tie-in, or regrading of the adjacent concrete walkway, that carries its own cost. We scope it upfront so nothing surprises you at the final invoice.
- Access and demolition. A long, narrow driveway with limited equipment access takes more labor than a wide-open lot. Concrete removal and hauling is also a line item when the existing surface has to come out.
- Sealing and finishing. We recommend sealing after the joint sand has cured, typically after the first 30 to 60 days. Sealing adds a line item but protects color and keeps the joint sand locked in over time.
A few practical notes on cost for Mesquite homeowners in planning mode: the free project estimate & design consult is genuinely free – we come out, measure the driveway, check the slope and drainage, and give you a written number with the itemized scope. We also apply the $1,000-off promotion to any project over $10,000, which typically covers the sealing and most of the drainage corrections in the same visit. And 0% financing for 18 months is available so you can spread a larger paver driveway across a comfortable timeline without interest.
For the broader context on how pavers compare with concrete, asphalt, and stone options, see our Driveway & Pavers in Mesquite overview – the cost drivers and material comparisons are laid out there in more detail.
FAQs – Brick Paver Driveway
How much does a brick paver driveway cost in Mesquite?
Expect roughly $9 to $18 per square foot installed, which puts a standard single-car driveway at $3,600 to $7,200 and a three-car driveway at $5,400 to $14,400. The final number depends on your base depth, paver material and pattern, and any drainage corrections the site needs. We give you the number upfront in writing before work begins. Call (888) 413-6358 for an exact quote – estimates are free.
How long does a brick paver driveway last in Mesquite’s climate?
A properly installed brick paver driveway should hold up for 30 to 50 years with regular joint sand top-ups and resealing every few years. The main variables are base preparation, edge restraint, and drainage – get those right and the pavers themselves outlast most concrete driveways. We install to a depth and compaction spec suited to the desert soil conditions here, and we back the workmanship with our 730-Day Done Right Promise.
Can you install a paver driveway over my existing concrete?
In most cases, no – not if you want the driveway to last. Installing pavers over cracked or moving concrete means the movement continues underneath and the pavers reflect the same cracks within a season or two. Removing the old surface and rebuilding the base is the right way to do it. There are narrow cases where an intact slab can serve as a base with an added layer and a bonding course, but we evaluate those in person. Call (888) 413-6358 and we’ll come out to take a look – estimates are free.
Can you fix a spreading paver driveway instead of replacing it?
Often yes. Spreading edges are usually a sign of an under-set edge restraint or a shallow base, both of which can be corrected by rebuilding the restrained edge, re-compacting the affected area, and re-laying the field units around it. We pull, reset, and re-sand as needed so the whole driveway matches. Call (888) 413-6358 to set up a free assessment – we’ll tell you whether repair or replacement is the better use of the budget.
Written by the team at Groundwork Construction Co. of Mesquite, serving Mesquite.
Reach a live person 24/7 at (888) 413-6358 for a free estimate and design consult on your brick paver driveway in Mesquite. We answer real calls – no voicemail, no waiting until Monday. Upfront pricing, background-checked uniformed technicians, and the 730-Day Done Right Promise on every paver driveway we install.


