







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Paver Driveways in Moapa Valley: What They Cost and What the Job Actually Involves
Paver driveways in Moapa Valley usually run $7,000 – $18,000 installed, with most acreage properties landing in the $11,000 – $16,000 range once you account for the longer runs out to a shop or barn. The job takes five to eight working days: two to three days of excavation and base prep, one day of base compaction and edge restraint, two to three days laying pavers, then a half day of cutting, sand, and cleanup. Call (888) 413-6358 to set up a free on-site estimate.
How We Install a Paver Driveway on a Moapa Valley Lot

Moapa Valley driveways are rarely a simple square. On a lot in Overton or Logandale, the driveway often runs 60 to 200 feet from the county road to a house, then splits again to reach a detached shop. That changes how we sequence the work. Here’s the order we follow.
- Stage 1 – Site walk and layout (day 1, about 2 hours). We mark the edges, confirm the slope away from the structure, and check where the well line, septic lateral field, and any buried electric to the shop run. If a fence sits close to the drive, we measure clearance for a 10-foot gate swing. You decide the final width here: 12 feet for a single vehicle lane, 16 to 20 feet where a truck and trailer need to pass.
- Stage 2 – Excavation and subgrade (days 1 – 3). We cut down 8 to 12 inches depending on paver thickness and soil. This is the part people underestimate. Muddy River alluvial soils and the expansive clay pockets north of the river corridor need more depth than a Las Vegas tract lot, because a shallow base cracks and heaves within two summers. We haul off spoils, which adds time and trucking cost.
- Stage 3 – Base, compaction, and drainage (day 3 – 4). We lay crushed aggregate in 4-inch lifts and compact each one. On a long rural drive we add a slight crown and a perimeter drain if runoff from the Mormon Mesa watershed crosses the pad. You decide whether water sheets to a landscape swale or into a dry well.
- Stage 4 – Edge restraint and paver laying (days 4 – 7). A concrete or steel edge goes down before the field pavers so the pattern doesn’t creep. We lay in the pattern you picked, cut edges to fit, and set a soldier course along the garage apron. This is the stage where a pattern change or a color shift is easy to make and, frankly, your last chance to change your mind cheaply.
- Stage 5 – Joint sand and cleanup (day 7 – 8). Polymeric sand sweeps into the joints, we mist it, and it sets. We walk the job with you, flag any chip or settle, and hand over the warranty in writing. Pavers are traffic-ready within 24 hours for foot traffic and a couple of days for vehicles.
You want the whole run usable in one pass, not a half-finished job that waits on a return trip. Everything above is scheduled back-to-back so we don’t leave you with a rutted dirt lane for a week. If the wider project also touches the approach, retaining, or patio edge, that lives under Driveway & Pavers in Moapa Valley and we plan it alongside the drive.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Pavers and Details You’ll Choose Between
Paver driveways are a materials decision as much as a labor decision, and the paver you pick changes both the look and the price by two to four thousand dollars on a typical Moapa Valley job. Here’s what we lay most and the trade-off on each.
- Concrete pavers (interlocking, tumbled). The workhorse. Rated for freeze-thaw and vehicle load, easy to repair one section at a time, and available in a dozen color blends. Belgard and similar lines run $5 to $9 per square foot for material. This is what we recommend for most rural drives.
- Clay brick pavers. Warmer look, strong color, but a harder hand to lay on a long curve and a higher material cost. Suits a ranch-style Overton frontage where the warm tone matches the masonry.
- Permeable pavers with an open-joint system. Worth considering on a lot that sees flash-flood runoff or where the county wants on-site water absorption. Costs 10 to 20 percent more than solid pavers but moves water through the surface instead of sheeting it toward the house.
- Paver thickness and pattern. 60mm is enough for a passenger drive. 80mm is the better call where a heavy truck, trailer, or RV parks regularly, and on the shop apron. Herringbone holds up best under turning tires; running bond is cheaper to lay and cleaner on a straight run.
What Paver Driveways Cost in Moapa Valley, NV?

Paver driveways in Moapa Valley run $7,000 to $18,000 for installation, based on square footage, base depth, run length, and paver grade. A short, simple 400-square-foot drive at the low end lands near $7,000. A 1,000-square-foot drive running out to a shop on a rural lot frequently tops $18,000, and here’s why.
- Square footage and run length. Material and labor scale nearly linearly, but long narrow runs cost more per foot than a wide pad because cutting and edging don’t shrink.
- Base depth and soil. Expansive clay and alluvial soils need 8 to 12 inches of base. Deeper base and more hauling push you toward the high end.
- Existing surface. A dirt lane is cheap to prep. Breaking out old concrete or asphalt first adds removal cost and trucking.
- Paver grade and thickness. Standard 60mm pavers are the baseline. 80mm heavy-duty pavers and permeable systems add 10 to 20 percent.
- Drainage and grading. A crown, perimeter drain, or dry well is extra, but skipping it on a floodplain lot is a false economy.
Our written estimate is line-item: excavation, haul-off, base, edge restraint, pavers by square foot, sand, and labor. What’s typically outside the estimate is landscape restoration beyond the drive edge, moving a well or septic line if it’s in the way, and any county floodplain review fee. Upfront pricing means the number you see is the number you pay; you don’t get a change order mid-job.
See the difference
Before
After
Before
After
Before
AfterWhat Moapa Valley Lots Specifically Do to a Paver Driveway Job
Moapa Valley is not a subdivision. It’s an agricultural oasis on the Muddy River, and the homes are a mix of older ranch-style and 1950s-70s masonry houses in Overton and Logandale, scattered custom builds, manufactured units, and a whole lot of farm outbuildings. That shapes a driveway job in ways a suburban contractor would miss.
The lots are large and often sit on well-and-septic infrastructure, so before we cut a single yard of base we confirm where the well head, septic tanks, and lateral fields run. Working around septic laterals is common on Warm Springs properties near Lake Mead. On unincorporated Clark County parcels the drive may also trigger floodplain review if it changes how water crosses the lot toward the river corridor, and we plan drainage around that. The soils are expansive in places, and the Mojave heat topping 110°F means we schedule base work and sand-setting into early mornings and cure carefully, not cook a fresh pad at 2 p.m. What we see failing on older drives here is shallow base: a thin pad that heaved after a wet spring and cracked along the joints. We fix that by digging to depth, not patching over it.
Serving Moapa Valley, NV – Our Local Coverage Area
We serve Moapa Valley and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Paver Driveways in Moapa Valley

Most paver driveways in Moapa Valley take five to eight working days from excavation to final sand. Long rural runs and deeper base push toward eight; a compact 400-square-foot drive can finish in five. Call (888) 413-6358 for a schedule estimate on your lot.
Often yes on unincorporated Clark County acreage, especially where the drive is new, changes drainage, or crosses near a floodplain or the septic system. We pull the required permits and coordinate the inspection as part of the job.
Yes in most cases. We lay out around fixed infrastructure and adjust the base and drainage so the well head and septic laterals stay protected. If a line truly blocks the drive, we flag it before we start rather than surprise you.
Expect roughly $13 to $22 per square foot installed, with the total landing between $7,000 and $18,000 depending on run length, base depth, and paver grade. Call (888) 413-6358 for an exact figure on your property; estimates are free.
Every paver driveway we install carries the 730-Day Done Right Promise: if it isn’t done right, we make it right. That covers workmanship for two full years, not just the first season.
Get a Free Paver Driveway Estimate in Moapa Valley
We’ll walk your lot, measure the run to the house and shop, and hand you a line-item written estimate for paver driveways in Moapa Valley at no charge. The call is answered by a live person any hour, and our technicians are background-checked and arrive in uniform. Reach us at (888) 413-6358 to book a free estimate and design consult, and if you’re planning more work, see our Driveway & Pavers service, the Moapa Valley area we cover, and homeowners often pair a new drive with Door Installation in Moapa Valley or Cabinets & Countertops in Moapa Valley.
Written by the team at Groundwork Construction Co.












